Content migration in progress, completing by midnight IST on 17 November 2026.
Home
Routing
This section guides you through configuring static or dynamic routing and managing
inbound and outbound traffic connections using Multi-Link configurations in SMCaaS to ensure network connectivity is optimized, load balanced, and highly available.
Configuring routing and anti-spoofing
Routing defines through which next hop router the Engine forwards traffic from a source address to a destination address. Anti-spoofing
defines which addresses are considered valid source addresses for the networks connected
to each interface.
Introduction to SMC as a Service
The SMC as a Service provides centralized access for configuring, managing, logging,
and monitoring NGFW s that secure network connectivity and control business operations.
Getting Started
The Getting Started section provides the information and procedures for downloading
software, acquiring licenses, and installing both software and physical appliances
to deploy SMCaaS for securing network connectivity and controlling business operations.
Routing
This section guides you through configuring static or dynamic routing and managing
inbound and outbound traffic connections using Multi-Link configurations in SMCaaS to ensure network connectivity is optimized, load balanced, and highly available.
Configuring routing and anti-spoofing
Routing defines through which next hop router the Engine forwards traffic from a source address to a destination address. Anti-spoofing
defines which addresses are considered valid source addresses for the networks connected
to each interface.
Getting started with routing
To understand how the Engine reads routing definitions, look at the network interfaces in the routing or anti-spoofing
configurations.
Routing configuration overview
Routing configuration involves adding a default route, adding routes to networks
that are not directly connected, and adding routes to networks that can be reached
through route-based VPNs.
Add routers
A Router element represents a next-hop gateway’s IP address in routing configurations.
Add or view the default route
You can check which route is currently set as the default route for traffic leaving
the Engine and set a new default route.
Add static routes
You can add a static route to a network in the routing configuration.
Configure DHCP message routing
The Engine can relay DHCP messages. If DHCP messages are routed through the Engine (from
a network segment to some other, isolated segment), you must enable DHCP relay on
the Engine interface properties for the interface where the DHCP requests
are originating from (client’s network).
Check routes using the Route Query tool
The Route Query tool allows you to check where packets with a certain IP address
are routed according to the current definitions. You can check that the routing is
correct and quickly find a particular branch in the Routing tree.
Remove static routes
New networks are automatically added to routing when you change the properties of
an interface. However, the Networks are not automatically removed, so you must check
the routing configuration for obsolete entries and remove them manually.
Modifying anti-spoofing
IP address spoofing is an attack where the source IP address in a packet is changed
to gain unauthorized access or to cause a denial-of-service. Such attacks can be prevented
with anti-spoofing rules.
Examples of routing configuration
The SMCaaS Application provides features that allow you to configure many routing scenarios.
Outbound traffic management
You can use Multi-Link to distribute outbound traffic between multiple network connections
and to provide high availability and load balancing for outbound traffic.
Inbound traffic management
Inbound traffic management ensures that services remain available even when one or
more servers or NetLinks fail, and balances the load of incoming traffic more efficiently
between a group of servers. Inbound traffic management is not supported on layer
2 physical interfaces on Engines.
Dynamic link selection
When you use Multi-Link for outbound traffic management or Multi-Link VPNs, SMCaaS can dynamically select the NetLink or VPN link that best matches the quality
requirements of traffic.
Advanced routing topics
Advanced routing capabilities in SMCaaS, including configurations for multiple routes
with metrics or ECMP, forced next hop routing, policy-based routing, multicast routing,
and dynamic routing protocols that enable engines to automatically adapt to network
topology changes.
Policy Creation and Administration
Monitoring
This section covers monitoring engines and system health, viewing and exporting logged
data, generating reports from logs and statistics, and filtering data to analyze network
traffic and application performance in SMCaaS.
VPN
Configuring routing and anti-spoofing
Routing defines through which next hop router the Engine forwards traffic from a source address to a destination
address. Anti-spoofing defines which addresses are considered valid source addresses for the networks connected to each interface.
Getting started with routing
To understand how the Engine reads routing definitions, look at the network interfaces in the routing or anti-spoofing configurations.
Routing configuration overview
Routing configuration involves adding a default route, adding routes to networks that are not directly connected, and adding routes to networks that can be reached through route-based VPNs.
Add routers
A Router element represents a next-hop gateway’s IP address in routing configurations.
Add or view the default route
You can check which route is currently set as the default route for traffic leaving the Engine and set a new default route.
Add static routes
You can add a static route to a network in the routing configuration.
Configure DHCP message routing
The Engine can relay DHCP messages. If DHCP messages are routed through the Engine (from a network segment to some other, isolated segment), you must enable DHCP relay on the Engine interface properties for the interface where the DHCP requests are originating from (client’s network).
Check routes using the Route Query tool
The Route Query tool allows you to check where packets with a certain IP address are routed according to the current definitions. You can check that the routing is correct and quickly find a particular branch in the Routing tree.
Remove static routes
New networks are automatically added to routing when you change the properties of an interface. However, the Networks are not automatically removed, so you must check the routing configuration for obsolete entries and remove them manually.
Modifying anti-spoofing
IP address spoofing is an attack where the source IP address in a packet is changed to gain unauthorized access or to cause a denial-of-service. Such attacks can be prevented with anti-spoofing rules.
Examples of routing configuration
The SMCaaS Application provides features that allow you to configure many routing scenarios.